帶V型槽的T型槽方箱使用標準

時間：2015/12/10 15:03:09 瀏覽量：382 1. 用途：方箱主要用于零部件的平行度、垂直度等的檢驗和劃線。方箱是用鑄鐵制成的具體6個工作面的空腔正方體，其中一個工作面上有V型槽。方箱檢定的環境條件：常溫、常濕。

2. 精度：對于刮研制方箱除檢定平面度外，還要用涂色法檢定接觸斑點。在邊長為25mm任意正方形內斑點數為：1級、2級不少于25點；3級不少于20點。

3. 技術要求：鑄鐵方箱：按JB/T3411.56-99標準制造，材料HT200。鑄件須經回火處理，不許有氣孔砂眼等鑄造缺陷，V型槽應對稱與各對應面的不垂直度不大于0.005，內表面涂紅色防銹油，工作面硬度為HB170-240. 方箱各工作面不能有銹跡、劃痕、裂紋、凹陷以及影響計量性能的其他缺陷。非工作面應清砂涂漆，棱邊倒角。在方箱內壁應有標牌，并標有規格尺寸，級別出廠編號、制造廠名稱。

4．鑄鐵方箱檢定方法：對于邊長為300mm及以下的方箱，檢定時在方箱被檢面的兩端各放置1mm的量塊，把刀口尺放在量塊工作面上，然后在其各被檢點處用量塊試塞，當量塊組剛剛?cè)霑r(shí)的尺寸與兩端量塊尺寸之差為該被檢點對兩端之間的偏差。這一檢定還應在方箱工作面的縱向、橫向和對角線方向的幾個截面上進行。在測得的各個位置的直線中誤差方向一致時取其最大值，當誤差方向不一致時取其最大正差與最大負差絕對值之和，為該受檢面平面的平面度。

1. Usage: Square box is mainly used for inspecting and marking parallelism and verticality of parts and components. Square box is a cube made of cast iron in six working faces, one of which has V-groove. Environmental conditions for box verification: normal temperature and humidity.
2. Accuracy: For scraping and developing square box, besides checking flatness, we also need to check contact spot by painting method. The number of spots in any square with 25 mm edge length is no less than 25 points in Grade 1 and grade 2, and no less than 20 points in grade 3.
3. Technical requirements: Cast iron square box: made according to JB/T3411.56-99 standard, material HT200. Castings shall be tempered without casting defects such as blowhole and sand holes, the non-perpendicularity of V-groove to the corresponding surface shall be no more than 0.005, the inner surface shall be coated with red anti-rust oil, and the hardness of the working face shall be HB170-240. There shall be no rust marks, scratches, cracks, depressions and other defects affecting the metering performance at all working faces of square boxes. Non-working face should be painted with clear sand and chamfered edges. There should be a sign on the inner wall of the box, with specifications and sizes, grade factory number and manufacturer name.
4. Verification method of cast iron square box: For square box with side length of 300 mm or less, 1 mm measuring blocks are placed at both ends of the checked side of the box, the knife ruler is placed on the working face of the measuring block, and then the test plug is used at each checked point. The difference between the size of the measuring block group just inserted and the size of the measuring blocks at both ends is the checked point pair. Deviation between ends. This verification should also be carried out on the longitudinal, transverse and diagonal sections of the square box working face. The flatness of the inspected plane is the sum of the absolute value of the maximum positive difference and the maximum negative difference when the direction of the error is the same in the straight line of each position measured, and the absolute value of the maximum positive difference and the maximum negative difference when the direction of the error is inconsistent.

Company name: botou zhuoyuan mechanical equipment manufacturing co.,LTD
Registered address: jiaohe development zone, botou city, hebei province
Fax number: 0317-8031093
Contact information: 15369812793 (WeChat with the same number)  liansheng chu
Postcode: 062151
Enterprise email:1358827475@qq.com
Account Opening Bank: Botou Branch of Bank of China
Account number: 100399943203
Agricultural bank account number: 6228481739059615270

http://zhuoyuanjixie.com